Help: Subwoofer Installation

Re: Help: Subwoofer Installation

I'll have to go ask a professional about the xOver because I have no idea what kind to look for. As for the REM, my stereo has a REM input for this type of jack:

[media]http://img.alibaba.com/photo/11730506/Audio_Extension_Cable.jpg[/media]

Should I just like cut it off something I don't use and connect it to the wire, or should I go to Bestbuy or something and buy a specific one for it?

So if the REM isn't connected, the amp won't turn on, correct?

Ya I know they're not the best subs, but I wasn't looking into spending a lot on really good ones. I don't really need/want anything better at the moment, especially since I don't have a new car yet and don't want to replace the battery and alternator on this one.

[TheHeartSmasher]

Re: Help: Subwoofer Installation

Yep, they are you regular Billy Bob subs but those 1,000 watt sub needs a 0/1 gauge wiring kit running at 1 to 4 ohm for the best performance .

[Xodus]

Re: Help: Subwoofer Installation

Remote is a wire that recieves a small current to tell the amp that the stereo is turned on, so the amp should turn itself on, or stand-by vice versa.

Remote, afaik, is usually pink, but it should be marked in a wiring diagram on top of the unit. But basiclly, it just goes from the head unit, to the amp.

MAKE SURE - You need to run the Power Cables on one side, of the car, and the RCA's / speaker cables through the center, or on the other side. If you don't, you will get a whine, that will get more high pitch as your RPM's go up.

And yeah, that diagram looks right, other than the REM wire, which isn't there yet.

I'm pretty sure you SHOULD get the xOver. I don't personally have one since on my sub, it's powered, so the xOver is built in. But my dad, who did Car stereo for over 13 years, says you should have one.

And TheHeartSmasher, we know it's not "Manly" subs (ignore that line Sam :P )

Re: Help: Subwoofer Installation

You need a Low Pass CrossOver Click - First off

Okay:

You take the RCA cables from the back of your stereo, to the amplifier, where it will go into the AUDIO IN. Then you would have the amp run in Mono Mode, and use any of the AudioOut (Speaker Cable's, not RCA) and run the ground, to the subwoofer ground. Then you would take that LowPass CrossOver I showed above, and it would go on the positive side, just one side on the cable come out of the amp, and the other side going into the subwoofer.

You DO NOT want the cross over that I linked you to, you want one that is compatible with 1000w's. Go down to somewhere that specializes in car audio, and ask them which kind you need, and then they can tell you in more detail how to install.

Is this what you're saying to do? If not, let me know what I did wrong. Also, what should I do with the REM on the amplifier? I'm pretty sure that's REMOTE and it should also go to the car stereo using the blue wire that was included with the wiring kit, correct? If so, where exactly do I put it in the car stereo? Also, is the low pass crossover filter necessary? My friend has his subwoofers working fine without it.

[media]http://img98.imageshack.us/img98/4048/77124207yi7.jpg[/media]

Sorry I'm asking these questions here, but I'm not ready to pay $150 for Bestbuy to install it.

WARNING!!! do not turn your XPLODs up too high or they will pop.
What gauge wire are you using for this? It should be 0/1 gauge @1/2/4 ohms or you may experience problems down the road.

I have the 1200W 8 gauge wiring kit.

[Jblankster]

Re: Help: Subwoofer Installation

Sure, I'll come by next saturday

ok cool, gonna ride your bike? im gonna wash mine that day

[TheHeartSmasher]

Re: Help: Subwoofer Installation

WARNING!!! do not turn your XPLODs up too high or they will pop.
What gauge wire are you using for this? It should be 0/1 gauge @1/2/4 ohms or you may experience problems down the road.

[Xodus]

Re: Help: Subwoofer Installation

^you think you can help hook my friends subs into his jeep liberty???!!! omg you be a car audio smarty pantz

Sure, I'll come by next saturday

[Jblankster]

Re: Help: Subwoofer Installation

^you think you can help hook my friends subs into his jeep liberty???!!! omg you be a car audio smarty pantz

[Xodus]

Re: Help: Subwoofer Installation

You need a Low Pass CrossOver Click - First off

Okay:

You take the RCA cables from the back of your stereo, to the amplifier, where it will go into the AUDIO IN. Then you would have the amp run in Mono Mode, and use any of the AudioOut (Speaker Cable's, not RCA) and run the ground, to the subwoofer ground. Then you would take that LowPass CrossOver I showed above, and it would go on the positive side, just one side on the cable come out of the amp, and the other side going into the subwoofer.

You DO NOT want the cross over that I linked you to, you want one that is compatible with 1000w's. Go down to somewhere that specializes in car audio, and ask them which kind you need, and then they can tell you in more detail how to install.

Re: Help: Subwoofer Installation

shouldent this be in the tech center ;S

Tried Google, didn't work.

1000W Sony XPLOD Subwoofer
1000W Sony XPLOD 1 Channel MOSFET Amplifier

I pretty much have everything setup, except the connection between the subwoofer and the amp. I'm not sure where on the amp I should plug the positive and negative cables coming from the subwoofer.

I have this setup:

High Level Input--------------------Speaker Out
(+) L (-) (-) R (+)-----------------(-) L + R (+) (-) L + R (+)

I'm almost positive I plug it into the Speaker Out side, but not sure which of the two.

Also wanted to make sure, the cable that runs from the radio to the amp is supposed to be connected to the INPUT or OUTPUT on the amp?

Last, where should I set the Filter, Low Boost, and Level at?